LT10M Manual Pallet Tilter, LT10E Eelectric Pallet Tilter

Introduction of pallet tilter

LT series lift and tilt pallet jack are designed to lift the pallet and tilt it to the ergonomic angle. LT10M manual pallet tilter & LT10E electric pallet tilter are worked to allow the users to ergonomically reach loads easily without having to bend down or over-stretch. The Electric tilt pallet jack has forced steering on one wheel to make manoeuvring easy. Lift /lower functions are controlled by a switch on the control lever. Tilt/return functions are controlled by a remote control, which is fitted with a long wire, and can make the operator and the tilter with load keep a certain distance, more safer. Lift /lower function and Tilt/return functions can be operated independently of each other or simultaneously. When Tilt/return functions are to be used, the tilter must be on a firm surface, and the universal wheel shall be braked. When Tilt/return functions are to be used to stack materials, the handle can be turned to the side to make access to the stack table easier.

As a pallet tilting equipment, this pallet jack tilter can be used as a pallet truck and also a tilting pallet truck, this can not only improve your work efficiency, but also save costs.

Pegangan dapat diputar dan dikunci dalam posisi jauh dari area kerja. Ini berlaku untuk posisi duduk dan berdiri. Garpu jack miring kemiringan dapat dimiringkan hingga 90 derajat. Keduanya disediakan sebagai standar dengan rem parkir dan pelindung kaki.

Sesuai dengan EN1757-1 dan EN1175

Details of pallet tilter

LT0M manual pallet tilter LT10E electric pallet tilter

We have this item in stock in France/US, if you are located in Europe or US, we can arrange delivery to you ASAP! This way will save your time and shipping cost.

Specifications of pallet tilter

i-lift No.		1520902	1520903
Model		LT10M	LT10E
Tipe		Manual	Listrik
Kapasitas	kg (lb.)	1000(2200)
Mengangkat tinggi, vertikal	h mm (dalam.)	285(11.2)
Tinggi badan minimum	h1 mm (masuk.)	85(3.3)
Panjang garpu	I mm (dalam.)	800(31.5)
Tangani tinggi	L1 mm (dalam.)	1138(44.8)
Lebar garpu keseluruhan	b mm (dalam.)	560(22)
Lebar antara garpu	b1 mm (dalam.)	234(9.2)
Panjang ujung garpu dari rol	L2 mm (masuk.)	135(5.3)
Lebar keseluruhan	B mm (dalam.)	638(25.1)
Panjang keseluruhan	L mm (dalam.)	1325(52.2)	1410(55.5)
Tinggi keseluruhan, terangkat	H mm (dalam.)	950(37.4)
Tinggi keseluruhan, diturunkan	H mm (dalam.)	750(29.5)
Pusat memuat Min./Max.	C1 mm (dalam.)	200/400(8/16)
Pusat memuat Min./Max.	C2 mm (masuk.)	200/420(8/16.5)
Unit Daya	KW / V	--	0.8/12
Berat bersih	kg (lb.)	178(391.6)	185(407)

Peraturan keselamatan

1. Driving the pallet tilter on the slope

1) The pallet tilter shall be unloaded or a small load.

2) Muatan harus berada di posisi terendah.

3) The gradient shall be no more than 2° when dragging the pallet tilter.

4) Operator akan berada pada posisi atas apakah upgrade atau downgrade.

2. Avoid offset loads

Beban harus didistribusikan secara merata pada garpu atau palet, dengan jarak 400mm antara pusat gravitasi dan garpu depan, ketinggian maksimum pusat gravitasi adalah 420mm, minimum 200mm, jarak keluar dari ruang lingkup ini akan mengurangi tingkat keamanan dan meningkatkan risiko.

Barang-barang di palet atau garpu harus diamankan dengan benar, hindari ketidakseimbangan muatan, sehingga tidak dapat jatuh selama pengangkutan, saat truk diangkat, atau ketika truk harus tetap diangkat untuk sementara waktu.

3. Driving loaded

The tilting pallet jack is designed for use on even and level floor. During transport the forks shall be raised as little as possible. Transport with raised forks should be made over the shortest possible distances and at low speed. Do not transport when tilting goods on the pallet tilter, this is not safe.

Peringatan: Jangan pernah meletakkan tangan atau kaki pada bagian yang bergerak, yang berisiko cedera.